View 74HC4852BQ-Q100_8377885.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1. general description the 74hc4852-q100; 74hct4852-q100 are high-speed si-gate cmos devices and are specified in compliance with jedec standard no. 7a. the 74hc4852-q100; 74hct4852-q100 are dual 4-channel analog multiplexers/demultiplexers wit h common select inputs (s0 an d s1). both multiplexers have a common active low enable input (e ), four independent inputs/outputs (ny0 to ny3) and two common inputs/outputs (1z, 2z). the devices feature injection-current effect control, which has excellent va lue in automotive applications wh ere voltages in excess of the supply voltage are common. with e low, two of the eight switches are selected (low impedance on-state) by s0 and s1. with e high, all switches are in the high-im pedance off-state, independent of s0 and s1. the injection-current effect c ontrol allows signals at disabl ed analog input channels to exceed the supply voltage without affecting the signal of the enabled analog channel. this eliminates the need for external diode/resistor networks typically used to keep the analog channel signals within the supply-voltage range. this product has been qualified to the automotive electronics council (aec) standard q100 (grade 1) and is suitable for use in automotive applications. 2. features and benefits ? automotive product qualif ication in accordance with aec-q100 (grade 1) ? specified from ? 40 ? c to +85 ? c and from ? 40 ? c to +125 ? c ? injection-current cro ss coupling < 1 mv/ma ? wide supply voltage range from 2.0 v to 6.0 v for 74hc4852-q100 ? esd protection: ? mil-std-883, method 3015 exceeds 2000 v ? hbm jesd22-a114f exceeds 2000 v ? mm jesd22-a115-a exceeds 200 v (c = 200 pf, r = 0 ? ) ? latch-up performance exceeds 100 ma per jesd 78 class ii level a ? low on-state resistance: ? 400 ? (typical) at v cc =2.0v ? 215 ? (typical) at v cc =3.0v ? 120 ? (typical) at v cc =3.3v ? 76 ? (typical) at v cc =4.5v ? 59 ? (typical) at v cc =6.0v 74hc4852-q100; 74hct4852-q100 dual 4-channel analog mult iplexer/demultiplexer with injection-current effect control rev. 1 ? 12 july 2012 product data sheet
74hc_hct4852_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved . product data sheet rev. 1 ? 12 july 2012 2 of 21 nxp semiconductors 74hc4852-q100; 74hct4852-q100 dual 4-channel analog multiplexer/demultiplexer with injection-current effect control 3. applications ? analog multiplexing and demultiplexing ? digital multiplexing and demultiplexing ? signal gating ? automotive application 4. ordering information 5. functional diagram table 1. ordering information type number package temperature range name description version 74hc4852d-q100 ? 40 ? c to +125 ? c so16 plastic small outl ine package; 16 leads; body width 3.9 mm sot109-1 74hct4852d-q100 74hc4852pw-q100 ? 40 ? c to +125 ? c tssop16 plastic thin shrink small outline package; 16 leads; body width 4.4 mm sot403-1 74hct4852pw-q100 74HC4852BQ-Q100 ? 40 ? c to +125 ? c dhvqfn16 plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 16 terminals; body 2.5 ? 3.5 ? 0.85 mm sot763-1 74hct4852bq-q100 fig 1. logic symbol fig 2. iec logic symbol 001aag093 1y0 12 13 3 1y1 s0 1z 2z 14 10 s19 6 e 1y3 11 2y0 1 2y2 2 2y3 4 2y1 5 1y2 15 1 0 mux/dmux 1 g4 5 2 4 3 13 12 14 15 11 0 1 2 3 0 1 2 3 001aag094 4 0 3 10 9 6
74hc_hct4852_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved . product data sheet rev. 1 ? 12 july 2012 3 of 21 nxp semiconductors 74hc4852-q100; 74hct4852-q100 dual 4-channel analog multiplexer/demultiplexer with injection-current effect control fig 3. functional diagram 001aag095 injection current control injection current control 1-of-4 decoder 8 6 9 10 gnd v cc 16 injection current control injection current control injection current control injection current control injection current control injection current control injection current control 1z 1y0 1y1 1y2 1y3 2y0 2y1 2y2 2y3 2z injection current control 13 12 14 15 11 1 5 2 4 3 s0 s1 e
74hc_hct4852_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved . product data sheet rev. 1 ? 12 july 2012 4 of 21 nxp semiconductors 74hc4852-q100; 74hct4852-q100 dual 4-channel analog multiplexer/demultiplexer with injection-current effect control 6. pinning information 6.1 pinning 6.2 pin description (1) this is not a supply pin. the substrate is attached to this pad using conductive die atta ch material. there is no electrical or mechanical requi rement to solder this pad. however, if it is soldered, the solder land should remain floating or be connected to gnd. fig 4. pin configuration so16 and tssop16 fig 5. pin configuration dhvqfn16 74hc4852-q100 74hct4852-q100 2y0 v cc 2y2 1y2 2z 1y1 2y3 1z 2y1 1y0 e 1y3 n.c. s0 gnd s1 aaa-003469 1 2 3 4 5 6 7 8 10 9 12 11 14 13 16 15 aaa-003470 74hc4852-q100 74hct4852-q100 n.c. s0 e 1y3 2y1 1y0 2y3 1z 2z 1y1 2y2 1y2 gnd s1 2y0 v cc transparent top view 7 10 6 11 5 12 4 13 3 14 2 15 8 9 1 16 terminal 1 index area gnd (1) table 2. pin description symbol pin description 2y0 1 independent input/output 2y2 2 independent input/output 2z 3 common input/output 2y3 4 independent input/output 2y1 5 independent input/output e 6 enable input (active low) n.c. 7 not connected gnd 8 ground (0 v) s1 9 select input s0 10 select input 1y3 11 independent input/output 1y0 12 independent input/output 1z 13 common input/output 1y1 14 independent input/output 1y2 15 independent input/output v cc 16 supply voltage
74hc_hct4852_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved . product data sheet rev. 1 ? 12 july 2012 5 of 21 nxp semiconductors 74hc4852-q100; 74hct4852-q100 dual 4-channel analog multiplexer/demultiplexer with injection-current effect control 7. functional description [1] h = high voltage level; l = low voltage level; x = don?t care. 8. limiting values [1] the minimum and maximum input voltage rating may be exceeded if the input clamping current rating is observed. [2] the minimum and maximum switch voltage rating may be ex ceeded if the switch clamping current rating is observed. [3] for so16 package: p tot derates linearly with 8 mw/k above 70 ? c. for tssop16 package: p tot derates linearly with 5.5 mw/k above 60 ? c. for dhvqfn16 packages: p tot derates linearly with 4.5 mw/k above 60 ? c. table 3. function table [1] input channel on e s1 s0 lllny0tonz llhny1tonz lhlny2tonz lhhny3tonz hxx- table 4. limiting values in accordance with the absolute maximum rating system (iec 60134). voltages are referenced to gnd (ground = 0 v). symbol parameter conditions min max unit v cc supply voltage ? 0.5 +7.0 v v i input voltage [1] ? 0.5 v cc +0.5 v v sw switch voltage [2] ? 0.5 v cc +0.5 v i ik input clamping current v i < ? 0.5 v or v i >v cc + 0.5 v - ? 20 ma i sk switch clamping current v sw < ? 0.5 v or v sw >v cc + 0.5 v - ? 20 ma i sw switch current v sw > ? 0.5 v or v sw < v cc + 0.5 v - ? 25 ma i cc supply current - 50 ma i gnd ground current ? 50 - ma t stg storage temperature ? 65 +150 ?c p tot total power dissipation t amb = ? 40 ? c to +125 ?c [3] - 500 mw
74hc_hct4852_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved . product data sheet rev. 1 ? 12 july 2012 6 of 21 nxp semiconductors 74hc4852-q100; 74hct4852-q100 dual 4-channel analog multiplexer/demultiplexer with injection-current effect control 9. recommended operating conditions 10. static characteristics table 5. recommended operating conditions symbol parameter conditions 74hc4852-q100 74hct4852-q100 unit min typ max min typ max v cc supply voltage 2.0 - 6.0 4.5 5.0 5.5 v v i input voltage 0 - v cc 0- v cc v v sw switch voltage 0 - v cc 0- v cc v t amb ambient temperature ? 40 - +125 ? 40 - +125 ?c ? t/ ? v input transition rise and fall rate v cc = 2.0 v - 6.0 1000 - - - ns/v v cc = 3.0 v - 6.0 800 - - - ns/v v cc = 3.3 v - 6.0 800 - - - ns/v v cc = 4.5 v - 6.0 500 - 6.0 500 ns/v v cc = 6.0 v - 6.0 400 - - - ns/v table 6. r on resistance at recommended operating conditions; voltages are re ferenced to gnd (ground 0 v); for test circuit see figure 8 . symbol parameter conditions 25 ?c ? 40 ? c to +85 ?c ? 40 ? c to +125 ?c unit min typ max min max min max 74hc4852-q100 r on(peak) on resistance (peak) v i = v cc to gnd; e = v il v cc = 2.0 v; i sw = 2 ma - 400 650 - 670 - 700 ? v cc = 3.0 v; i sw ? 2 ma - 215 330 - 360 - 380 ? v cc = 3.3 v; i sw ?? 2 ma - 120 270 - 305 - 345 ? v cc = 4.5 v; i sw ?? 2 ma - 76 210 - 240 - 270 ? v cc = 6.0 v; i sw ?? 2 ma - 59 195 - 220 - 250 ? ? r on on resistance mismatch between channels v i = 0.5 ? v cc ; e = v il v cc = 2.0 v; i sw = 2 ma - 4 10 - 15 - 20 ? v cc = 3.0 v; i sw ? 2ma - 2 8 - 12 - 16 ? v cc = 3.3 v; i sw ?? 2ma - 2 8 - 12 - 16 ? v cc = 4.5 v; i sw ?? 2ma - 2 8 - 12 - 16 ? v cc = 6.0 v; i sw ?? 2ma - 3 9 - 13 - 18 ? 74hct4852-q100 r on(peak) on resistance (peak) v i = v cc to gnd; e = v il v cc = 4.5 v; i sw ?? 2 ma - 76 210 - 240 - 270 ? ? r on on resistance mismatch between channels v i = 0.5 ? v cc ; e = v il v cc = 4.5 v; i sw ?? 2ma - 2 8 - 12 - 16 ?
74hc_hct4852_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved . product data sheet rev. 1 ? 12 july 2012 7 of 21 nxp semiconductors 74hc4852-q100; 74hct4852-q100 dual 4-channel analog multiplexer/demultiplexer with injection-current effect control [1] typical values are measured at t amb = 25 ? c. [2] ? v o here is the maximum variation of output voltage of an enabled analog channel when current is injected into any disabled channe l. [3] i sw = total current injected into all disabled channels. table 7. injection current coupling at recommended operating conditions; voltages are re ferenced to gnd (ground 0 v); for test circuit see figure 9 . symbol parameter conditions 74hc4852/q100 74hct4852/q100 unit min typ [1] max min typ [1] max t amb = ? 40 ? c to +125 ?c ? v o output voltage variation ?i sw ?? 1 ma; r s ?? 3.9 k ? [2] [3] v cc = 3.3 v - 0.05 1 - - - mv v cc = 5.0 v - 0.03 1 - 0.03 1 mv ?i sw ? ? 10 ma; r s ?? 3.9 k ? v cc = 3.3 v - 0.55 5 - - - mv v cc = 5.0 v - 0.27 5 - 0.27 5 mv ?i sw ?? 1 ma; r s ?? 20 k ? v cc = 3.3 v - 0.04 2 - - - mv v cc = 5.0 v - 0.03 2 - 0.03 2 mv ?i sw ?? 10 ma; r s ?? 20 k ? v cc = 3.3 v - 0.56 20 - - - mv v cc = 5.0 v - 0.48 20 - 0.48 20 mv table 8. static characteristics at recommended operating conditions; volt ages are referenced to gnd (ground 0 v). 25 ?c ? 40 ?c to +85 ?c ? 40 ? c to +125 ?c symbol parameter conditions min typ max min max min max unit 74hc4852-q100 v ih high-level input voltage control inputs v cc = 2.0 v 1.5 - - 1.5 - 1.5 - v v cc = 3.0 v 2.1 - - 2.1 - 2.1 - v v cc = 3.3 v 2.3 - - 2.3 - 2.3 - v v cc = 4.5 v 3.15 - - 3.15 - 3.15 - v v cc = 6.0 v 4.2 - - 4.2 - 4.2 - v v il low-level input voltage control inputs v cc = 2.0 v - - 0.5 - 0.5 - 0.5 v v cc = 3.0 v - - 0.9 - 0.9 - 0.9 v v cc = 3.3 v - - 1.0 - 1.0 - 1.0 v v cc = 4.5 v - - 1.35 - 1.35 - 1.35 v v cc = 6.0 v - - 1.8 - 1.8 - 1.8 v i i input leakage current control inputs; v i =gndorv cc v cc = 6.0 v - - ? 0.1 - ? 0.1 - ? 1.0 ? a
74hc_hct4852_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved . product data sheet rev. 1 ? 12 july 2012 8 of 21 nxp semiconductors 74hc4852-q100; 74hct4852-q100 dual 4-channel analog multiplexer/demultiplexer with injection-current effect control i s(off) off-state leakage current e = v ih ; v i = gnd or v cc ; v o =v cc or gnd; v cc = 6.0 v; see figure 6 nyn; per channel - - ? 0.1 - ? 0.5 - ? 1.0 ? a nz; all channels - - ? 0.2 - ? 2.0 - ? 4.0 ? a i s(on) on-state leakage current e = v il ; v i = gnd or v cc ; v o =v cc or gnd; v cc = 6.0 v; see figure 7 -- ? 0.1 - ? 0.5 - ? 1.0 ? a i cc supply current v i = gnd or v cc v cc = 6.0 v - - 2.0 - 5.0 - 20.0 ? a c i input capacitance s0, s1, s2 and e - 2 10 - 10 - 10 pf c sw switch capacitance nz; off-state - 15 40 - 40 - 40 pf nyn; off-state - 3 15 - 15 - 15 pf 74hct4852-q100 v ih high-level input voltage control inputs v cc = 4.5 v to 5.5 v 2.0 - - 2.0 - 2.0 - v v il low-level input voltage control inputs v cc = 4.5 v to 5.5 v - - 0.8 - 0.8 - 0.8 v i i input leakage current control inputs; v i =gndorv cc v cc = 5.5 v - - ? 0.1 - ? 0.1 - ? 1.0 ? a i s(off) off-state leakage current e = v ih ; v i = gnd or v cc ; v o =v cc or gnd; v cc = 5.5 v; see figure 6 per channel - - ? 0.1 - ? 0.5 - ? 1.0 ? a all channels - - ? 0.2 - ? 2.0 - ? 4.0 ? a i s(on) on-state leakage current e = v il ; v i = gnd or v cc ; v o =v cc or gnd; v cc = 5.5 v; see figure 7 -- ? 0.1 - ? 0.5 - ? 1.0 ? a i cc supply current v i = gnd or v cc v cc = 5.5 v - - 2.0 - 5.0 - 20.0 ? a ? i cc additional supply current control inputs; v i =v cc ? 2.1 v; other inputs at v cc or gnd; v cc = 4.5 v to 5.5 v; i o =0a - - 300 - 370 - 370 ? a c i input capacitance s0, s1, s2 and e - 2 10 - 10 - 10 pf c sw switch capacitance nz; off-state - 9 40 - 40 - 40 pf nyn; off-state - 3 15 - 15 - 15 pf table 8. static characteristics ?continued at recommended operating conditions; volt ages are referenced to gnd (ground 0 v). 25 ?c ? 40 ?c to +85 ?c ? 40 ? c to +125 ?c symbol parameter conditions min typ max min max min max unit
74hc_hct4852_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved . product data sheet rev. 1 ? 12 july 2012 9 of 21 nxp semiconductors 74hc4852-q100; 74hct4852-q100 dual 4-channel analog multiplexer/demultiplexer with injection-current effect control (1) channel is selected by s0 and s1. fig 6. test circuit for measuring off-state leakage current fig 7. test circuit for measuring on-state leakage current i s 001aag098 i s v i v ih e nyn nz v cc gnd v o 001aag099 v o v il e nyn nz v cc gnd i s v i nyn selected channel (1) any disabled channel n.c. r on = v sw / i sw . (1) channel is selected by s0 and s1. v i (1) < gnd or v i (1) > v cc . gnd < v i (2) < v cc . fig 8. test circuit for measuring on resistance fig 9. test circuit for injection current coupling 001aag100 v sw v i v il e nyn nz v cc gnd i sw v 001aag101 v i r s v il v i (1) v i (2) e nyn nz v cc gnd i sw nyn any disabled channel selected channel (1) v o
74hc_hct4852_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved . product data sheet rev. 1 ? 12 july 2012 10 of 21 nxp semiconductors 74hc4852-q100; 74hct4852-q100 dual 4-channel analog multiplexer/demultiplexer with injection-current effect control 11. dynamic characteristics table 9. dynamic characteristics at recommended operating conditions; voltages are re ferenced to gnd (ground 0 v); for load circuit see figure 14 . symbol parameter conditions 25 ?c ? 40 ? c to +85 ?c ? 40 ? c to +125 ?c unit min typ max min max min max 74hc4852-q100 t pd propagation delay nz, nyn to nyn, nz; see figure 10 [1] v cc = 2.0 v 2.2 9.3 33 2.2 34 2.2 35 ns v cc = 3.0 v 2.2 4.9 16.5 1.9 18 1.9 19.5 ns v cc = 3.3 v 2.0 4.4 15.0 1.6 16.5 1.6 18.5 ns v cc = 4.5 v 1.6 3.2 11.6 1.1 12.5 1.1 13.5 ns v cc = 6.0 v 1.5 2.5 10.2 0.9 11 0.9 12 ns sn to nz, nyn; see figure 11 [1] v cc = 2.0 v 7.7 16.8 38 6.3 40 6.3 42 ns v cc = 3.0 v 4.9 8.8 20 3.9 21.5 3.9 23 ns v cc = 3.3 v 4.4 7.9 17.5 3.4 19 3.4 22 ns v cc = 4.5 v 3.2 5.8 14 2.3 15 2.3 17 ns v cc = 6.0 v 2.4 4.8 12.6 1.6 14.5 1.6 16.5 ns t en enable time e to nz, nyn; see figure 12 [2] v cc = 2.0 v 10.5 20.5 47.5 8.5 52.5 8.5 57.5 ns v cc = 3.0 v 6.2 10.6 45 5.2 50 5.2 55 ns v cc = 3.3 v 5.6 9.4 42.5 4.6 47.5 4.6 52.5 ns v cc = 4.5 v 4.2 6.9 40 3 45 3 50 ns v cc = 6.0 v 3.2 5.6 39 2.2 40 2.2 40 ns t dis disable time e to nz, nyn; see figure 12 [3] v cc = 2.0 v 39.5 75.4 100 39.3 105 39 115 ns v cc = 3.0 v 35.2 69.5 90 35.5 100 35 110 ns v cc = 3.3 v 34.6 68.1 85 34.6 95 34.5 105 ns v cc = 4.5 v 28.5 63 80 28.2 90 28 100 ns v cc = 6.0 v 14.4 57.9 78 13.5 80 13.0 80 ns c pd power dissipation capacitance per channel; see figure 13 [4] v cc = 3.3 v - 42 - - - - - pf v cc = 5.0 v - 47 - - - - - pf
74hc_hct4852_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved . product data sheet rev. 1 ? 12 july 2012 11 of 21 nxp semiconductors 74hc4852-q100; 74hct4852-q100 dual 4-channel analog multiplexer/demultiplexer with injection-current effect control [1] t pd is the same as t plh and t phl . [2] t en is the same as t pzh and t pzl . [3] t dis is the same as t plz and t phz . [4] c pd is used to determine the dynamic power dissipation (p d in ? w): p d =c pd ? v cc 2 ? f i + ? {(c l +c sw ) ? v cc 2 ? f o } where: f i = input frequency in mhz; f o = output frequency in mhz; ? {(c l +c sw ) ? v cc 2 ? f o } = sum of outputs; c l = output load capacitance in pf; c sw = switch capacitance in pf; v cc = supply voltage in v. 12. waveforms 74hct4852-q100 t pd propagation delay nz, nyn to nyn, nz; see figure 10 [1] v cc = 4.5 v 1.6 3.5 11.5 1.1 12.5 1.1 13.5 ns sn to nz, nyn; see figure 11 [1] v cc = 4.5 v 3.2 7.6 13 2.3 15 1.6 17 ns t en enable time e to nz, nyn; see figure 12 [2] v cc = 4.5 v 4.2 8.3 25 3.0 30 3.0 35 ns t dis disable time e to nz, nyn; see figure 12 [3] v cc = 4.5 v 28.5 61.8 80 28.2 90 28.0 100 ns c pd power dissipation capacitance per channel; see figure 13 [4] v cc = 5.0 v - 47 - - - - - pf table 9. dynamic characteristics ?continued at recommended operating conditions; voltages are re ferenced to gnd (ground 0 v); for load circuit see figure 14 . symbol parameter conditions 25 ?c ? 40 ? c to +85 ?c ? 40 ? c to +125 ?c unit min typ max min max min max fig 10. input (nz, nyn) to output (nyn, nz) propagation delays 001aah578 v cc nz or nyn input nyn or nz output t plh 0.5v cc 0.5v cc t phl gnd v cc gnd
74hc_hct4852_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved . product data sheet rev. 1 ? 12 july 2012 12 of 21 nxp semiconductors 74hc4852-q100; 74hct4852-q100 dual 4-channel analog multiplexer/demultiplexer with injection-current effect control measurement points are given in table 10 . fig 11. input (sn) to output (nyn, nz) propagation delays 001aah579 t plh t phl v m v m v i gnd sn input nyn or nz output v cc gnd measurement points are shown in table 10 . logic levels: v ol and v oh are typical output voltage levels that occur with the output load. fig 12. enable and disable times 001aah580 t plz t phz switch off switch on v y v x switch on nz or nyn output nz or nyn output e input v i v ol v oh v cc v m v m 0 v gnd t pzl t pzh v m v m table 10. measurement points type input output v m v i v m v x v y 74hc4852-q100 0.5v cc v cc 0.5v cc v ol + 0.1(v cc ? v ol )0.9v oh 74hct4852-q100 1.3 v 3.0 v 0.5v cc v ol + 0.1(v cc ? v ol )0.9v oh
74hc_hct4852_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved . product data sheet rev. 1 ? 12 july 2012 13 of 21 nxp semiconductors 74hc4852-q100; 74hct4852-q100 dual 4-channel analog multiplexer/demultiplexer with injection-current effect control fig 13. test circuit for measuring power dissipation capacitance 001aah581 selected channel disabled channel v cc nyn sn nyn n.c. nz gnd e a g
74hc_hct4852_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved . product data sheet rev. 1 ? 12 july 2012 14 of 21 nxp semiconductors 74hc4852-q100; 74hct4852-q100 dual 4-channel analog multiplexer/demultiplexer with injection-current effect control [1] for 74hct4852-q100: input voltage v i = 3.0 v. a. input pulse definition definitions for test circuit: r l = load resistance. c l = load capacitance including jig and probe capacitance. r t = termination resistance should be equal to the output impedance z o of the pulse generator. b. load circuit test data is given in table 11 . fig 14. input pulse definition and load circuit 001aac221 v m v m t w t w 10 % 90 % 90 % 0 v v i v i negative pulse positive pulse 0 v v m v m 90 % 10 % 10 % t f t r t r t f 001aaf883 v cc gnd v i v o v cc open r t r l c l dut switch g table 11. test data test input output s1 position control e , sn switch nyn (nz) t r , t f switch nz (nyn) v i [1] v i c l r l t phl, t plh v cc v cc 6ns 50pf - open t phz , t pzh v cc v cc 6ns 50pf 10k ? gnd t plz , t pzl v cc v cc 6ns 50pf 10k ? v cc c pd v cc v cc 6ns 0 pf - open
74hc_hct4852_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved . product data sheet rev. 1 ? 12 july 2012 15 of 21 nxp semiconductors 74hc4852-q100; 74hct4852-q100 dual 4-channel analog multiplexer/demultiplexer with injection-current effect control 13. package outline fig 15. package outline sot109-1 (so16) x w m a a 1 a 2 b p d h e l p q detail x e z e c l v m a (a ) 3 a 8 9 1 16 y pin 1 index unit a max. a 1 a 2 a 3 b p cd (1) e (1) (1) eh e ll p qz ywv references outline version european projection issue date iec jedec jeita mm inches 1.75 0.25 0.10 1.45 1.25 0.25 0.49 0.36 0.25 0.19 10.0 9.8 4.0 3.8 1.27 6.2 5.8 0.7 0.6 0.7 0.3 8 0 o o 0.25 0.1 dimensions (inch dimensions are derived from the original mm dimensions) note 1. plastic or metal protrusions of 0.15 mm (0.006 inch) maximum per side are not included. 1.0 0.4 sot109-1 99-12-27 03-02-19 076e07 ms-012 0.069 0.010 0.004 0.057 0.049 0.01 0.019 0.014 0.0100 0.0075 0.39 0.38 0.16 0.15 0.05 1.05 0.041 0.244 0.228 0.028 0.020 0.028 0.012 0.01 0.25 0.01 0.004 0.039 0.016 0 2.5 5 mm scale so16: plastic small outline package; 16 leads; body width 3.9 mm sot109-1
74hc_hct4852_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved . product data sheet rev. 1 ? 12 july 2012 16 of 21 nxp semiconductors 74hc4852-q100; 74hct4852-q100 dual 4-channel analog multiplexer/demultiplexer with injection-current effect control fig 16. package outline sot403-1 (tssop16) unit a 1 a 2 a 3 b p cd (1) e (2) (1) eh e ll p qz ywv references outline version european projection issue date iec jedec jeita mm 0.15 0.05 0.95 0.80 0.30 0.19 0.2 0.1 5.1 4.9 4.5 4.3 0.65 6.6 6.2 0.4 0.3 0.40 0.06 8 0 o o 0.13 0.1 0.2 1 dimensions (mm are the original dimensions) notes 1. plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. plastic interlead protrusions of 0.25 mm maximum per side are not included. 0.75 0.50 sot403-1 mo-153 99-12-27 03-02-18 w m b p d z e 0.25 18 16 9 a a 1 a 2 l p q detail x l (a ) 3 h e e c v m a x a y 0 2.5 5 mm scale tssop16: plastic thin shrink small outline package; 16 leads; body width 4.4 mm sot403-1 a max. 1.1 pin 1 index
74hc_hct4852_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved . product data sheet rev. 1 ? 12 july 2012 17 of 21 nxp semiconductors 74hc4852-q100; 74hct4852-q100 dual 4-channel analog multiplexer/demultiplexer with injection-current effect control fig 17. package outline sot763-1 (dhvqfn16) terminal 1 index area 0.5 1 a 1 e h b unit y e 0.2 c references outline version european projection issue date iec jedec jeita mm 3.6 3.4 d h 2.15 1.85 y 1 2.6 2.4 1.15 0.85 e 1 2.5 0.30 0.18 0.05 0.00 0.05 0.1 dimensions (mm are the original dimensions) sot763-1 mo-241 - - - - - - 0.5 0.3 l 0.1 v 0.05 w 0 2.5 5 mm scale sot763-1 dhvqfn16: plastic dual in-line compatible thermal enhanced very thin quad flat package; no leads; 16 terminals; body 2.5 x 3.5 x 0.85 mm a (1) max. a a 1 c detail x y y 1 c e l e h d h e e 1 b 27 15 10 9 8 1 16 x d e c b a terminal 1 index area ac c b v m w m e (1) note 1. plastic or metal protrusions of 0.075 mm maximum per side are not included. d (1) 02-10-17 03-01-27
74hc_hct4852_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved . product data sheet rev. 1 ? 12 july 2012 18 of 21 nxp semiconductors 74hc4852-q100; 74hct4852-q100 dual 4-channel analog multiplexer/demultiplexer with injection-current effect control 14. abbreviations 15. revision history table 12. abbreviations acronym description cdm charged device model cmos complementary metal oxide semiconductor dut device under test esd electrostatic discharge hbm human body model mm machine model table 13. revision history document id release date data sheet status change notice supersedes 74hc_hct4852_q100_1 20120712 product data sheet - -
74hc_hct4852_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved . product data sheet rev. 1 ? 12 july 2012 19 of 21 nxp semiconductors 74hc4852-q100; 74hct4852-q100 dual 4-channel analog multiplexer/demultiplexer with injection-current effect control 16. legal information 16.1 data sheet status [1] please consult the most recently issued document before initiating or completing a design. [2] the term ?short data sheet? is explained in section ?definitions?. [3] the product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple device s. the latest product status information is available on the internet at url http://www.nxp.com . 16.2 definitions draft ? the document is a draft versi on only. the content is still under internal review and subject to formal approval, which may result in modifications or additions. nxp semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall hav e no liability for the consequences of use of such information. short data sheet ? a short data sheet is an extract from a full data sheet with the same product type number(s) and title. a short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. for detailed and full information see the relevant full data sheet, which is available on request vi a the local nxp semiconductors sales office. in case of any inconsistency or conflict with the short data sheet, the full data sheet shall prevail. product specification ? the information and data provided in a product data sheet shall define the specification of the product as agreed between nxp semiconductors and its customer , unless nxp semiconductors and customer have explicitly agreed otherwis e in writing. in no event however, shall an agreement be valid in which the nxp semiconductors product is deemed to offer functions and qualities beyond those described in the product data sheet. 16.3 disclaimers limited warranty and liability ? information in this document is believed to be accurate and reliable. however, nxp semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such info rmation. nxp semiconductors takes no responsibility for the content in this document if provided by an information source outside of nxp semiconductors. in no event shall nxp semiconductors be liable for any indirect, incidental, punitive, special or consequential damages (including - without limitation - lost profits, lost savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on tort (including negligence), warranty, breach of contract or any other legal theory. notwithstanding any damages that customer might incur for any reason whatsoever, nxp semiconductors? aggregate and cumulative liability towards customer for the products described herein shall be limited in accordance with the terms and conditions of commercial sale of nxp semiconductors. right to make changes ? nxp semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice. this document supersedes and replaces all information supplied prior to the publication hereof. suitability for use in automotive applications ? this nxp semiconductors product has been qualified for use in automotive applications. unless otherwise agreed in writing, the product is not designed, authorized or warranted to be suitable for use in life support, life-critical or safety-critical systems or equipment, nor in applications where failure or malfunction of an nxp semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. nxp semiconductors and its suppliers accept no liability for inclusion and/or use of nxp semiconducto rs products in such equipment or applications and therefore such inclusion and/or use is at the customer's own risk. applications ? applications that are described herein for any of these products are for illustrative purpos es only. nxp semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or modification. customers are responsible for the design and operation of their applications and products using nxp semiconductors products, and nxp semiconductors accepts no liability for any assistance with applications or customer product design. it is customer?s sole responsibility to determine whether the nxp semiconductors product is suitable and fit for the customer?s applications and products planned, as well as fo r the planned application and use of customer?s third party customer(s). customers should provide appropriate design and operating safeguards to minimize the risks associated with their applications and products. nxp semiconductors does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer?s applications or products, or the application or use by customer?s third party customer(s). customer is responsible for doing all necessary testing for the customer?s applic ations and products using nxp semiconductors products in order to av oid a default of the applications and the products or of the application or use by customer?s third party customer(s). nxp does not accept any liability in this respect. limiting values ? stress above one or more limiting values (as defined in the absolute maximum ratings system of iec 60134) will cause permanent damage to the device. limiting values are stress ratings only and (proper) operation of the device at these or any other conditions above those given in the recommended operating conditions section (if present) or the characteristics sections of this document is not warranted. constant or repeated exposure to limiting values will permanently and irreversibly affect the quality and reliability of the device. terms and conditions of commercial sale ? nxp semiconductors products are sold subject to the gener al terms and conditions of commercial sale, as published at http://www.nxp.com/profile/terms , unless otherwise agreed in a valid written individual agreement. in case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. nxp semiconductors hereby expressly objects to applying the customer?s general terms and conditions with regard to the purchase of nxp semiconducto rs products by customer. document status [1] [2] product status [3] definition objective [short] data sheet development this document contains data from the objecti ve specification for product development. preliminary [short] data sheet qualification this document contains data from the preliminary specification. product [short] data sheet production this document contains the product specification.
74hc_hct4852_q100 all information provided in this document is subject to legal disclaimers. ? nxp b.v. 2012. all rights reserved . product data sheet rev. 1 ? 12 july 2012 20 of 21 nxp semiconductors 74hc4852-q100; 74hct4852-q100 dual 4-channel analog multiplexer/demultiplexer with injection-current effect control no offer to sell or license ? nothing in this document may be interpreted or construed as an offer to sell products t hat is open for acceptance or the grant, conveyance or implication of any licens e under any copyrights, patents or other industrial or intellectual property rights. export control ? this document as well as the item(s) described herein may be subject to export control regu lations. export might require a prior authorization from competent authorities. translations ? a non-english (translated) version of a document is for reference only. the english version shall prevail in case of any discrepancy between the translated and english versions. 16.4 trademarks notice: all referenced brands, produc t names, service names and trademarks are the property of their respective owners. 17. contact information for more information, please visit: http://www.nxp.com for sales office addresses, please send an email to: salesaddresses@nxp.com
nxp semiconductors 74hc4852-q100; 74hct4852-q100 dual 4-channel analog multiplexer/demultiplexer with injection-current effect control ? nxp b.v. 2012. all rights reserved. for more information, please visit: http://www.nxp.com for sales office addresses, please se nd an email to: salesaddresses@nxp.com date of release: 12 july 2012 document identifier: 74hc_hct4852_q100 please be aware that important notices concerning this document and the product(s) described herein, have been included in section ?legal information?. 18. contents 1 general description . . . . . . . . . . . . . . . . . . . . . . 1 2 features and benefits . . . . . . . . . . . . . . . . . . . . 1 3 applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 4 ordering information . . . . . . . . . . . . . . . . . . . . . 2 5 functional diagram . . . . . . . . . . . . . . . . . . . . . . 2 6 pinning information . . . . . . . . . . . . . . . . . . . . . . 4 6.1 pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 6.2 pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 7 functional description . . . . . . . . . . . . . . . . . . . 5 8 limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 5 9 recommended operating conditions. . . . . . . . 6 10 static characteristics. . . . . . . . . . . . . . . . . . . . . 6 11 dynamic characteristics . . . . . . . . . . . . . . . . . 10 12 waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 13 package outline . . . . . . . . . . . . . . . . . . . . . . . . 15 14 abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 18 15 revision history . . . . . . . . . . . . . . . . . . . . . . . . 18 16 legal information. . . . . . . . . . . . . . . . . . . . . . . 19 16.1 data sheet status . . . . . . . . . . . . . . . . . . . . . . 19 16.2 definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 16.3 disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 16.4 trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . 20 17 contact information. . . . . . . . . . . . . . . . . . . . . 20 18 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

▲Up To Search▲

Price & Availability of 74HC4852BQ-Q100

	To Download 74HC4852BQ-Q100 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .